• Available in different sizes including:


    2 oz Needle Bottle(2N)
    2 oz Screw Top(2F)
    4 oz Needle Bottle(4N)
    4 oz Pump Spray(4P)
    5 oz Aerosol (GS-5A)
    11 oz Aerosol(11A)
    1 Gallon(1G)
    5 Gallon(5G)
    55 Gallon(5G)

  • GETSOME1000 Applications & Uses

  • Our Products

  • ENGINEERING

    CUTTING, TAPPING AND MILLING LUBRICANT:

    GETSOME 1000 is considered as being the best cutting and machining lubricant for aluminum and aluminum alloys. It gives a clean and smooth finish and stops the problems of tool chatter, tool creep, furring and burring that are normally associated with working those metals. GETSOME 1000 is a good lubricant for drilling, tapping and thread cutting of all metals. GETSOME 1000 will reduce the instances of work hardening when used as a lubricant for the machining of stainless steel and will give this metal a clean, smooth finish.

     

    GETSOME 1000 is a good machine cutting lubricant for all metals and their alloys. It is not affected by cutting oil viruses or the problems associated with soluble oil type lubricants. GETSOME 1000 never needs replacing, just top up the reservoir as it is used up. GETSOME 1000 will keep reservoirs, pumps and feed lines clean and free from corrosion. GETSOME 1000 can be used by a hand held applicator for individual and one off machining applications. GETSOME 1000 is a good lubricant for metal plate cutting blades as used on guillotines.

     

    STAMPING AND PUNCHING:

     

     

    GETSOME 1000 lubricant will allow metal to be cleanly hole punched and stamped without sticking or jamming, just spray or paint a liberal coat on GETSOME 1000 on the plate metal and bars to be stamped or punched or coat the punch tool or stamp.

     

     

    WELDING AND COATINGS:

    GETSOME 1000 is a good lubricant for wire feeders on MIG welders, stops jamming and corrosion and allows the wire to feed smoothly. Spray GETSOME 1000 on ferrous steel welds (especially on jobs built outside in the open air) to protect against rust forming until painting or powder coating is done. GETSOME 1000 can be painted over with oil based primers without first removing the GETSOME 1000 coating. Once cleaned with white spirits, GETSOME 1000 is compatible with powder coating. GETSOME 1000 is easily removed with white spirit or most mineral based solvents.  GETSOME 1000 will not harm painted, enameled and powder coated surfaces or finishes.

     

    LUBRICATION & PROTECTION:

    GETSOME 1000 has a fine enough texture so that it can be used to lubricate and protect venire calipers and micrometers from rust and corrosion. Spray GETSOME 1000 on finished steel and alloy parts and fittings, example, crankshafts, engine blocks, cam shafts, production line machined fittings, to protect them against corrosion and extend their shelf life until used. Use GETSOME 1000 to protect against corrosion and lubricate for trouble free operation, spindles, chucks, tool clamps, threaded shafts, fastenings, lathe beds, etc, on power hacksaws, milling machine, lathes, drilling and boring machines. GETSOME 1000 will protect from corrosion between use, milling heads, reamers and cutting tools. GETSOME 1000 will protect any bare metal surfaces on machines against corrosion. GETSOME 1000 will help protect against rust, new plate, bar, rod and tube steel stored in the open air. Use GETSOME 1000 to clean hand tools and keep them free from corrosion.

     

    SOLUBLE OIL TYPE CUTTING LUBRICANTS:

    GETSOME 1000 is not compatible with soluble oil type cutting lubricants, reservoirs and feed lines must be flushed clean before using GETSOME 1000 as a cutting oil lubricant. Because most soluble oil type cutting lubricants have no anti-corrosion component, rust and corrosion can form on lathes and milling machines using this type of lubricant. GETSOME 1000 will protect engineering equipment and stop corrosion, but the soluble oil must be washed off first or GETSOME 1000 may lose its’ effectiveness in protecting this equipment. GETSOME 1000 will draw any corrosion out of the pores of the metal and quite commonly the next day after applying GETSOME 1000, equipment can have a reddish brown coating, this is caused by the cleaning action of GETSOME 1000 drawing corrosion to the surface of the metal. By spraying on more GETSOME 1000 and wiping with a coarse weave cotton cloth will clean away the leached corrosion deposits and allow GETSOME 1000 to continue to keep equipment clean and corrosion free.

     

    HOT CAUSTIC CLEANING BATHS:

    This type of cleaning bath is designed for effectively cleaning grease, baked on oil resins and carbon from engine parts and blocks before regrinding and reboring. Depending on where the caustic bath is situated, inside or outside the building, the caustic fumes can have an effect on anti-corrosion coatings on finished parts up to 50 feet from where the bath is sited. GETSOME 1000 is a very good anti-corrosion product for finished metal surfaces, but its effectiveness can be impaired by fumes from a caustic bath. Always store finished engine parts and blocks well away from where the caustic bath is situated. There are no set rules for this situation; trial and error is the only way to determine a safe distance.  For extra corrosion protection use GETSOME  XTREME.